However, there are several situations which may require a different type of transducer. Inboard boats, wood or metal hulls, and sail boats create unique transducer mounting needs Alternate transducers and mounting methods are detailed below. The installation guide included on the next few pages provides detailed step by step instructions for installation of the control head and transducer.
For transom mount transducer installations you will need the mounting template included with your manual. Page 6 Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct installation of your transducer. Due to the wide variety of boat hulls, only general instructions are presented in the installation guide. Page 7 If the propeller s is are forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered.
Step Two - Drill the Mounting Holes 1. Remove the mounting template from the front of the Operations Manual. Apply silicone sealant to the mounting holes drilled into the transom. Align the transducer assembly with the drilled holes in the transom Figure 8. Page 10 mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed.
Page 11 If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' 15 m.
Call Humminbird Customer Support for more information. Follow these steps to route the cable through the transom: 1. Page 12 Inside the hull mounting generally produces good results in single thickness fiberglass-hulled boats. Humminbird cannot guarantee depth performance when transmitting and receiving through the hull of the boat since some signal loss occurs. The amount of loss depends on hull construction and thickness, and the installation. Sign Up or Sign In. Powered by. Badges Report an Issue Terms of Service.
Humminbird sx fishfinder owners manual. Download: Humminbird sx fishfinder owners manual Read Online: Humminbird sx fishfinder owners manual humminbird ci hd manuel francais humminbird c si humminbird helix g3n tuto humminbird solixsondeur humminbird new humminbird humminbird c manual humminbird logo Browse 1 Humminbird Wide W manuals for free PDF download: User's Manual. Your Humminbird fishfinder consists of two primary components to install: the control head and the transducer.
The control head contains the sonar transmit and receive circuitry, as well as the user controls and display. It should be installed in a location that provides access to the controls and visibility while in use. The control head mounts on a quick disconnect mounting system that swivels and tilts providing flexibility for viewing from almost anywhere on the boat.
The transducer converts electrical energy from the transmitter into mechanical pulses or sound waves. The transducer also receives the reflected sound waves and converts them back into electrical signals for display on the control head. It should be installed in contact with the surface of the water in an area that has smooth waterflowusually on the transom of the boat.
There are several mounting options for the transducer. Review the following section to determine the method that works for you and your boat. Your Humminbird fishfinder includes a standard transducer.
This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat. The transom installation, which is the most widely used, places the transducer on the outside of the boat hull.
This technique produces the least signal loss, and provides a way to adjust the transducer after installation. The mounting hardware included is designed to protect both the boat and the transducer should the boat strike debris in the water or when trailering.
As an alternative to transom mounting, it is possible on many fiberglass-hulled boats to glue the transducer on the inside of the boat hull. Since fiberglass has similar sonar characteristics as water, the sonar signal can pass through the boat hull with minimal loss. The hull of the boat must be single layer construction not double-hulled Also, any air trapped in the lamination of the fiberglass would prevent the sonar signal from passing through. Inside the hull installations require no holes be drilled into the boat and through experimentation, high-speed.
Two-part slow cure epoxy not included is required to glue the transducer in place. Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats. However, there are several situations which may require a different type of transducer. Inboard boats, wood or metal hulls, and sail boats create unique transducer mounting needs Alternate transducers and mounting methods are detailed below. The standard transducer can be adapted for portable installations with a portable mounting kit available from Humminbird.
This accessory adapts your transducer to a suction cup mount for temporary installation on the boat hull or other surface. Humminbird Matrix FF Installation 2. Humminbird NS10 2. Humminbird NS25 2. Humminbird PC Connect 2. Humminbird PMax 1. Humminbird PMax 30 1. Humminbird Piranha1 2 IN 2. Humminbird Piranha1 2 OP 2. Humminbird Piranha3 4 5 OP 2. Humminbird Piranha3 4 IN 2. Humminbird Piranha5 IN 2. Humminbird Piranha PT 2.
Humminbird Platinum ID 1. Humminbird Platinum Portable 1. Humminbird Pro Angler 2. Humminbird Pro Flasher 2M.
Humminbird RF15 1. Humminbird RF20 2. Humminbird RF25 2M. Humminbird RF30 2M. Humminbird RF35 1. Humminbird RF40 3M. Humminbird RF45 1. Humminbird Screen Capture Manual 1.
0コメント